Our Insightful Blog

Explore technical deep dives, ASIC design methodologies, sub-3nm DFT innovations, and semiconductor manufacturing insights from SignOff’s engineering team.

DFT & Silicon Architecture

Exploring Future Silicon Architecture & Sub- 3nm DFT Innovations

6 min read
Embark on an engineering journey as we explore on-chip compression logic, scan chain routing optimization, and automated pattern generation across advanced FinFET and…

ASIC Tape-out

From Architecture to Silicon: An ASIC Tape-out Journey

ASIC Tape-out

From Architecture to Silicon: An ASIC Tape-out Journey

Explore Our Latest Articles

Optical Proximity Correction (OPC)

Layout Blog: Standard Cells

IC Design & Flow Overview

STA-2

Ways to fix setup violations: Setup violation occurs because of high delay in the data path or due to negative skew. Below are the ways to fix setup violation: Gate sizing Buffering

Boolean Expressions-2

We hope you had a good understanding of Boolean Expressions which is available @ Boolean Expressions. In this blog, we will discuss on the simplification of boolean functions.

Logic Gates

We hope you had a good understanding of Number Systems which is available @ Number Systems. For building hardware, we need logic gates, combinational circuits and sequential circuits which takes input in the form of binary numbers. The main building blocks to design combinational and sequential circuits are logic gates which is explained below.

Boolean Expressions-1

We hope you had a good understanding of Logic Gates which is available @ Logic Gates. To reduce the logical complexities of any Boolean expression, a set of theorems have been developed which is explained below.

Number Systems

To start with VLSI skill development, we need to enhance our frontend skills. check the ASIC flow at ASICvsFPGA, which describes the frontend and backend flow for the full chip development. Frontend starts with specification gathering and architecture designing from the specifications gathered.

ASIC vs FPGA

Before starting the discussion on what is ASIC and what is FPGA, we will first learn about the basics that a VLSI enthusiast should know. Moore’s Law: Moore’s law is the observation that the number of transistors in a dense integrated circuit doubles about every two years.

Introduction to SDC

Before starting the discussion on what is ASIC and what is FPGA, we will first learn about the basics that a VLSI enthusiast should know. Moore’s Law: Moore’s law is the observation that the number of transistors in a dense integrated circuit doubles about every two years.

Gate All Around FET

GAA is somehow similar to FinFETs except the conducting channel is surrounded by gate all around. Thus we get better gate controllability over the channel. The channel shape can be square or any other polygon shape.

Communication Protocols

UART stands for Universal Asynchronous Receiver-Transmitter. It is commonly used in the microcontroller to communicate with the peripheral. An 8-bit serial data coming from the peripheral device is converted into the parallel form using serial to parallel conversion and parallel data coming from the CPU is converted using parallel to serial conversion.

Bulk CMOS

CMOS technology uses both NMOS and PMOS transistors, The transistors are arranged in a structure formed by two complementary networks. Bulk CMOS is a chip built on a standard silicon wafer.

FinFET-2 (Multi-Gate FinFET)

In 1965, Gorden Moore in his paper predicted that how number of transistors in integrated circuit get double in every 18 month. Even though in 1990, a new type of substrate named SOI (Silicon-on-insulator) was introduced which improved the speed and power consumption, the first integrated circuit transistor was fabricated on “Bulk” silicon wafers.

Silicon On Insulator ( SOI )

Silicon on insulator (SOI) refers to the use of a three layered substrate in place of conventional bulk silicon substrates. A thin layer of silicon is placed on top of an insulator such as silicon dioxide (SiO2) also known as a buried oxide layer.

UPF

Power is one of the most concerned factor in the lower node technologies due to sophisticated operation of a system at higher frequencies, complex functionalities, wireless applications and portability. Power dissipation has become one of the critical issues as it results in heating up of the device which in-turn affects the operation of a chip.

Post CTS Optimization

During Clock tree synthesis, buffers or inverters are added in the clock nets to achieve minimum Insertion delay and Skew, while meeting the clock DRV’s. Various optimizations are performed during CTS such as CCDO (Concurrent Clock and Data Optimization) and CTO (Clock Tree Optimization) .

STA-1

What is STA ? Static timing analysis is one of the techniques used to verify the timing of a digital design. STA is static since the analysis of the design is carried out statically and does not depend upon the data values being applied at the input pins of the design.

Pulse Width Reduction

What is the need of balanced buffers in clock path (Pulse Width Violation) ? Balanced buffers are preferred for clock tree synthesis. If unbalanced buffers (unequal rise & fall time) are used in CTS, then pulse width reduces & minimum pulse width violation occurs.

FinFET-1

What are FinFETs?FinFETs are non-planar transistors built on SOI or Bulk substrate. FinFET describes any fin-based, multi-gate transistor architecture, regardless of the number of gates.