[vc_row][vc_column][vc_column_text]

Silicon On Insulator ( SOI )

 

Author : Abhishek Kumar, Physical Design Engineer, SignOff Semiconductors

Author: Ankit Varma, Physical Design Engineer, Signoff Semiconductors

[/vc_column_text][vc_column_text]

Silicon on insulator (SOI) refers to the use of a three layered substrate in place of conventional bulk silicon substrates. A thin layer of silicon is placed on top of an insulator such as silicon dioxide (SiO2) also known as a buried oxide layer. This layer lies upon the substrate and isolates the body from the substrate. The transistors are then built upon the thin silicon layer. The full dielectric isolation of the devices reduces parasitic capacitance, thereby improving performance.

The choice of the insulating layer depends largely on the intended application. Sapphire is used for high performance radio frequency (RF) and Radiation sensitive applications & SiO2 is used for diminished short channel effects in microelectronic devices.

[/vc_column_text][vc_column_text]

What is the need of SOI ?


[/vc_column_text][vc_column_text]

Types of SOI devices

There are two different types of SOI devices:

1. Partially Depleted Silicon On Insulator (PD-SOI)

In a PDSOI N-type MOSFET, top silicon layer is thicker and the holes are pushed toward the buried oxide layer creating a region called floating body, which can store charge. That creates a modified switching threshold point, which depends on the history of the circuit. The inversion region does not extend the full depth of the body leaving a floating body in the channel. The insulating buried oxide layer is also thicker and channel is doped. The partially depleted SOI device behaves similarly to the bulk device, except that charge can accumulate in the body and modify its characteristics.Simpler technology with no wells and trenches.

Problems associated with PD-SOI

[/vc_column_text][vc_column_text]

2. Fully Depleted Silicon On Insulator (FD-SOI)

FD-SOI is a planar process technology with two major changes made in bulk CMOS technology. First, an ultra-thin layer of insulator, called the buried oxide, is placed on top of the base silicon substrate. Then, a very thin silicon film placed on top of insulating layer implements the pmos and nmos devices. Silicon layer under the gate is so thin that it is fully depleted of mobile charge carriers and no doping is required in the channel. when the channel is very lightly doped and very thin, the depletion region fills the full length of the body, thus eliminating the floating body region. The combination of these two innovations is called “ultra-thin body and buried oxide Fully Depleted SOI” or UTBB-FD-SOI.

Body Biasing: In order to improve transistor performance a voltage can be applied to the substrate. This method called body biasing or back biasing facilitates the creation of the chaannel between the source and the drain resulting in faster switching of the transistor.
In bulk CMOS, body biasing is very limited due to leakage current and reduced transistor geometry. Because of the ultra thin insulator layer in FD-SOI, the body biasing creates a buried gate below the channel making the FD-SOI act like a vertical double gate transistor.

Different voltages can be applied to the top and buried gates which effectively changes the characteristics of the transistor. FD-SOI can be made to work in either high performance mode or low power mode based on the voltages applied on top and buried gates.

Many techniques have been used in producing the SOI materials:

[/vc_column_text][vc_column_text]

CMOS fabrication by SOI technology:-

The subsequent steps for fabrication of CMOS SOI are similar to Bulk Technology.

Fig1: SOI structure

Fig2: Island formation

Fig3: Poly Si gates

Fig4: P+ drain / source

Fig5: N+ drain / source

Fig6: Metallization

[/vc_column_text][vc_column_text]

Advantages of SOI over bulk CMOS process:-

  1. Better electrostatic control of the channel.
  2. Reduction of parasitic junction capacitances.
  3. Excellent latchup immunity because of buried oxide layer.
  4. Limited short channel effects compared to bulk CMOS technology.
  5. Reduced subthreshold leakage and diode leakage.
  6. Higher speed and lower power consumption.
  7. Gives high-performance and cost-effective alternative to bulk CMOS technology.
  8. Smaller transistor saves lot of area and provides higher packaging density.
  9. Radiation tolerance – Reduced soft error rates, which refers to change of data in the memory for space application because of radiations.
  10. Involves fewer manufacturing and processing steps than bulk CMOS technology.
  11. Simpler technology with no wells and trenches.
  12. Substrate noise is reduced because the burried oxide layer acts as a dielectric barrier.

Problems:

  1. Self-heating due to the low thermal conductivity of the buried oxide.
  2. History effect (Floating body effect) in PD-SOI.
  3. Difficulty in manufacturing thin body SOI wafers in FD SOI.

[/vc_column_text][/vc_column][/vc_row]