Introduction

Optical Proximity Correction OPC is a resolution enhancement technique based on optical lithography. It is used in sub-wavelength lithography to deal with the severe image distortions. These image distortions typically include the: increased corner rounding, line-end shortening and changes in the width when located in isolated or dense environments. This technique helps in improving the imaging resolution. It is very important for the OPC to be efficient, especially for full-chip modification with complicated circuit layout in advanced technology nodes.

OPC is widely used in lithography for increasing the achievable resolution and pattern transfer fidelity in IC manufacturing. The OPC is based on the fundamental idea of modifying the mask itself for the correction of non-idealities that occur during the pattern transfer.

The main technique utilized to create VLSI circuits is optical microlithography. The success of this technology is attributable to the simplicity with which optical projection printing can transfer layout patterns to silicon, leading to excellent yield and throughput. These lithography advancements over the past fifteen years have significantly contributed to lowering design rules for device sizes This miniaturization effort has been motivated by the need for circuits that operate more quickly and efficiently.

With the further progress in lithography, the size of the devices could go down to 0.10 um and even below. However, we reach the limits of lithography and pattern transfer before reaching at such dimensions. The loss of image quality in optical lithography at smaller dimensions erodes the design-to-wafer fidelity on silicon. Yet, equipment costs, established production knowledge, and a tight production schedule act as conservative forces, helping in keeping the optical lithography viable in this range.

With the present outlook, optical lithography will remain an essential part of pattern transfer for both the economic and technological reasons, well into the 21st century. In order to further increase the lifetime of optical lithography, integrated circuit (IC) manufacturers are seeking for ways of enhancing resolution. The traditional way of increasing resolution and therefore shrinking dimensions can be achieved by using smaller wavelengths and better optics. However, the speed of technology development at smaller wavelengths is slower than the speed at which the designs are shrinking. Increasing resolution and/or compensating for pattern transfer non-idealities at the mask level mask engineering can be an alternative strategy to smaller wavelengths and improved illumination. The approach of making systematic modifications to mask geometries to compensate for pattern transfer non-idealities is typically called Optical Proximity Correction (OPC).

What is OPC?

OPC is the advanced mask engineering technique that can be used to increase layout-to-wafer pattern fidelity. The objective of OPC is to enhance optical characteristics by adjusting the mask. This is done by accounting for known effects that will happen during imaging or later processing by adjusting the mask geometry.

Why we need OPC?

Earlier when the Lithography was chosen as a basic process for semiconductor manufacturing, then the features were large as compared to the wavelength of light. Presently, the feature sizes are smaller as compared to the wavelength of even invisible radiation. As a result of this, the features exposed on the chip by mask do not exactly match the drawn features of the mask. As illustrated in figure below:

The features that are drawn on the mask result in distorted features on the wafer, this effect is called as optical proximity. The fabricated features will differ from the forms on the corrected mask, but by altering the masks, we may get the fabricated features to look the way we want them to.

Lithography

Lithography is the key technology used in semiconductor manufacturing. It is the process of transferring geometric patterns in a mask to the surface of silicon wafer. In this process, the wafer surface on which the pattern is to be transferred is covered with the radiation-sensitive material called as the resist and then it is exposed to the radiation. The radiation is transmitted through the clear parts of the mask as the exposed photoresist is insoluble in the developer solution. Then the etching process is performed to remove the unexposed portion of the wafer surface. In this way, the required geometric patterns in a mask are transferred onto the surface of the wafer.

The process of Lithography is based on the following factors:

                     NA is proportional to Diameter of the lens/focal length

                     Resolution = k (λ/NA)

Optical Lithography and Its Types

Optical lithography is the process in which the visible or ultraviolet radiation is used to transfer mask patterns onto the surface of the wafer. The masks used in optical lithography are usually made of glass or chromium.

Optical is further classified as:

Demerit: As the mask is in direct contact with the wafer, this significantly reduces the life of the mask.

Merit: – Since there is a small gap in between the mask and the wafer, this   increases the life of the mask.

     Merit: – No distortion, Good resolution

     Demerit – The process is costly.

Automated approaches to OPC

There have been several suggested automated OPC methods. These can be generally divided into two categories:

These techniques are simple to implement, and have comparatively low cost and high throughput. These techniques are very popular in semiconductor industry and are widely applicable in several technology nodes.

Optical Proximity Correction Techniques

The Optical Proximity Correction is carried in the following ways:

By these techniques, masks are analyzed and then it is determined that where the problem may occur. And based on the analysis done, the masks are modified to correct for the optical proximity effects. For the exact correction, it requires continuous curves on the masks which cannot be fabricated. There are some OPC tools, which allow the user to select the accuracy of the mask correction and also the allowable tolerance between the ideal and actual correction.

Advantages of OPC

Advantages: – OPC has the following advantages:

Disclaimer:

The purpose of this blog is to spread knowledge and facilitate open discussions. The content shared is based on our research from diverse sources including the internet, books, and conversations with others. We strive for accuracy; however, we acknowledge the possibility of errors or omissions. We value your input and encourage you to share your comments, questions, and suggestions. We are open to clarifying or correcting any inaccuracies found within the blog. 

Please note that while we appreciate your contributions, we may not be able to implement all suggestions. The blog should not be considered a substitute for professional advice.